How to Draw a Mug

Чекор по чекор

1. Чекор 1

   Одлучи го нивото на окото и обележај го.

   Everything about the ellipses follows from this. If the mug is below your eye level you will see into it; if it is level you will not. Make the decision consciously now rather than letting it drift halfway through the drawing.

   Внимавај! Not deciding, then drawing a rim that contradicts the base.

   Проверка You should be able to say whether you are looking down into this mug or across at it.

2. Чекор 2

   Нацртај го облогот како еден елипса, со едно брзо движење.

   Go round three or four times without stopping and keep the best pass. Speed is what makes an ellipse smooth - drawn slowly it comes out lumpy on one side every single time, because your hand cannot hold a curve at low speed.

   Внимавај! Building it out of short careful arcs.

   Проверка It should be symmetrical about its own long axis.

3. Чекор 3

   Нацртај ги двете страни право надолу, малку се снижава.

   Start exactly at the ends of the ellipse's long axis. A slight taper inward looks more natural than perfectly parallel sides, and it is what most real mugs do.

   Внимавај! Starting the sides inside or outside the rim, which leaves a visible step.

   Проверка Each side should begin exactly at the widest point of the rim.

4. Чекор 4

   Затвори го дното со елипса малку поокругла од врвот.

   The base is further from your eye level than the rim, so it is rounder. Same width, more curve. Getting this relationship right is the difference between a mug that sits on the table and one that appears to be sliding off it.

   Внимавај! Drawing the base flatter than the rim, or as a straight line.

   Проверка Rounder than the rim, and exactly the same width.

5. Чекор 5

   Додај втора крива во рамото.

   This thin band is the thickness of the ceramic, and it is what makes the top read as an opening rather than a painted disc. One stroke, following the rim's curve.

   Внимавај! Drawing it parallel all the way round instead of following the ellipse.

   Проверка There should be a visible band between the two curves at the front.

6. Чекор 6

   Нацртај ја надворешната крива на рачката.

   Start just below the rim and end about two-thirds of the way down the side. Both ends must touch the mug - a handle that floats beside the body is the most common error here and it is instantly visible.

   Внимавај! Leaving a gap where the handle meets the mug.

   Проверка Both ends of the curve should touch the side of the mug.

7. Чекор 7

   Дајте ја дебелината на држката со втора крива внатре.

   A handle is a strap, not a wire. The inner curve runs parallel to the outer one and meets the mug slightly closer in at both ends. This is a small change that makes a large difference to how solid the mug looks.

   Внимавај! Drawing the handle as a single line.

   Проверка There should be a visible gap between the two handle curves.

8. Чекор 8

   Маркирај од каде доаѓа светлината.

   Pick a side and commit. A cylinder shades differently from a sphere - the darkest band sits just inside the edge on the shadow side, not at the very edge, because light bounces back up off the table onto the rim.

   Внимавај! Shading the very edge darkest, which makes the mug look flat.

   Проверка You should be able to say which side is lit.

9. Чекор 9

   Засенчи ја страна на шољата од светлината.

   Work in one direction rather than scrubbing back and forth. Scrubbing gives an even grey, which is exactly the thing that makes a drawing look flat, so lay the strokes the same way and build the darkness in passes.

   Внимавај! Being too timid. Beginners routinely stop two or three steps short of dark enough.

   Проверка The dark side should be clearly darker than the mid tone, not slightly.

10. Чекор 10

    Додадете запалка на работ од сенка.

    Light bouncing off the table catches the very edge of a cylinder, so the darkest band sits slightly INSIDE the outline. Leaving that thin lighter strip is what makes the mug read as round rather than as a shaded rectangle.

    Внимавај! Running the shading right up to the outline.

    Проверка There should be a thin lighter line between your shading and the edge.

11. Чекор 11

    Додај ја сенката на површината под него.

    The cast shadow is darkest where it touches the mug and softens as it moves away. It also anchors the object to a surface - without it the mug floats, however well you have shaded it.

    Внимавај! Drawing it as an even grey blob detached from the object.

    Проверка It should touch the object and be darkest at that contact point.

12. Чекор 12

    Оди преку линиите што сакаш да ги задржиш и изгуби ги водичите.

    This is the step that turns a construction drawing into a finished one, and it is the one most people skip. Press harder on the outline and the features; leave the small stuff light. That difference in weight is what makes a drawing look deliberate rather than traced, and it costs thirty seconds.

    Внимавај! Going over everything at the same weight, which flattens the drawing back out.

    Проверка The outline should be clearly darker than the smallest details.