How to Draw a Mug

Hakbang-hakbang

1. Hakbang 1

   Magpasya ang iyong antas ng mata at markahan ito.

   Everything about the ellipses follows from this. If the mug is below your eye level you will see into it; if it is level you will not. Make the decision consciously now rather than letting it drift halfway through the drawing.

   Mag-ingat Not deciding, then drawing a rim that contradicts the base.

   Tingnan You should be able to say whether you are looking down into this mug or across at it.

2. Hakbang 2

   I-draw ang rim bilang isang tambilugan, sa isang solong mabilis na galaw.

   Go round three or four times without stopping and keep the best pass. Speed is what makes an ellipse smooth - drawn slowly it comes out lumpy on one side every single time, because your hand cannot hold a curve at low speed.

   Mag-ingat Building it out of short careful arcs.

   Tingnan It should be symmetrical about its own long axis.

3. Hakbang 3

   I-draw ang dalawang panig tuwid pababa, taper sa bahagyang.

   Start exactly at the ends of the ellipse's long axis. A slight taper inward looks more natural than perfectly parallel sides, and it is what most real mugs do.

   Mag-ingat Starting the sides inside or outside the rim, which leaves a visible step.

   Tingnan Each side should begin exactly at the widest point of the rim.

4. Hakbang 4

   Isara ang ibaba na may isang tambilugan bahagyang rounder kaysa sa tuktok.

   The base is further from your eye level than the rim, so it is rounder. Same width, more curve. Getting this relationship right is the difference between a mug that sits on the table and one that appears to be sliding off it.

   Mag-ingat Drawing the base flatter than the rim, or as a straight line.

   Tingnan Rounder than the rim, and exactly the same width.

5. Hakbang 5

   Magdagdag ng isang ikalawang kurva lamang sa loob ng rim.

   This thin band is the thickness of the ceramic, and it is what makes the top read as an opening rather than a painted disc. One stroke, following the rim's curve.

   Mag-ingat Drawing it parallel all the way round instead of following the ellipse.

   Tingnan There should be a visible band between the two curves at the front.

6. Hakbang 6

   I-draw ang panlabas na kurva ng handle.

   Start just below the rim and end about two-thirds of the way down the side. Both ends must touch the mug - a handle that floats beside the body is the most common error here and it is instantly visible.

   Mag-ingat Leaving a gap where the handle meets the mug.

   Tingnan Both ends of the curve should touch the side of the mug.

7. Hakbang 7

   Magbigay ng hawakan kapal na may isang ikalawang kurva sa loob.

   A handle is a strap, not a wire. The inner curve runs parallel to the outer one and meets the mug slightly closer in at both ends. This is a small change that makes a large difference to how solid the mug looks.

   Mag-ingat Drawing the handle as a single line.

   Tingnan There should be a visible gap between the two handle curves.

8. Hakbang 8

   Mark kung saan ang ilaw ay mula sa.

   Pick a side and commit. A cylinder shades differently from a sphere - the darkest band sits just inside the edge on the shadow side, not at the very edge, because light bounces back up off the table onto the rim.

   Mag-ingat Shading the very edge darkest, which makes the mug look flat.

   Tingnan You should be able to say which side is lit.

9. Hakbang 9

   Shade ang gilid ng mug ang layo mula sa ilaw.

   Work in one direction rather than scrubbing back and forth. Scrubbing gives an even grey, which is exactly the thing that makes a drawing look flat, so lay the strokes the same way and build the darkness in passes.

   Mag-ingat Being too timid. Beginners routinely stop two or three steps short of dark enough.

   Tingnan The dark side should be clearly darker than the mid tone, not slightly.

10. Hakbang 10

    Magdagdag ng isang lighter strip karapatan sa lilim-side gilid.

    Light bouncing off the table catches the very edge of a cylinder, so the darkest band sits slightly INSIDE the outline. Leaving that thin lighter strip is what makes the mug read as round rather than as a shaded rectangle.

    Mag-ingat Running the shading right up to the outline.

    Tingnan There should be a thin lighter line between your shading and the edge.

11. Hakbang 11

    Idagdag ang lilim sa ibabaw sa ibaba.

    The cast shadow is darkest where it touches the mug and softens as it moves away. It also anchors the object to a surface - without it the mug floats, however well you have shaded it.

    Mag-ingat Drawing it as an even grey blob detached from the object.

    Tingnan It should touch the object and be darkest at that contact point.

12. Hakbang 12

    Pumunta sa ibabaw ng mga linya na nais mong panatilihin, at mawalan ng mga gabay.

    This is the step that turns a construction drawing into a finished one, and it is the one most people skip. Press harder on the outline and the features; leave the small stuff light. That difference in weight is what makes a drawing look deliberate rather than traced, and it costs thirty seconds.

    Mag-ingat Going over everything at the same weight, which flattens the drawing back out.

    Tingnan The outline should be clearly darker than the smallest details.