How to Draw a Pig

Step by step

1. Step 1

   Block in the ribcage as one big oval.

   The ribcage is the largest single mass in almost every four-legged animal, and drawing it too small is the most common structural error in the whole category. Draw it in one motion and make it bigger than feels right.

   Tarira Drawing the chest small to leave room for everything else.

   Check The chest oval should take up around a third of the body's length on its own.

2. Step 2

   Place the second mass, the pelvis, behind the ribcage.

   The gap between the two masses is information: it is most of what separates a long animal from a compact one. Decide the gap deliberately rather than letting it happen.

   Tarira Butting the pelvis directly against the chest.

   Check You should see clear space between the two ovals.

3. Step 3

   Link the two ovals with one curve - that is the spine.

   One continuous curve, drawn in one pass. The spine sets the whole animal's attitude, and a spine assembled from three short strokes reads as three different animals stitched together.

   Tarira Drawing the spine as separate flat segments.

   Check The curve should touch both masses without a corner.

4. Step 4

   Sketch the head mass and the direction of the neck.

   Note where the neck leaves the chest before you place the skull - on most animals it comes off the front of the chest mass, not the top, and that single angle carries the species.

   Tarira Hanging the head above the body instead of in front of it.

   Check The neck guide should leave the FRONT half of the chest oval.

5. Step 5

   Draw the neck as a solid, not a stick.

   A neck is a solid with real thickness, and on most animals it is thicker than you think - nearly as deep as the head itself. Two curves, one over, one under.

   Tarira A thin stick neck, which makes any animal look fragile.

   Check The neck should be nearly as thick as the head is tall.

6. Step 6

   Draw the topline and the belly to join the masses up.

   This is where the animal stops being two eggs. Let the topline follow the spine you already drew and keep the belly line taut - a sagging belly is a decision, not an accident.

   Tarira Ignoring the spine curve you drew and inventing a new back.

   Check The topline should agree with the spine curve underneath it.

7. Step 7

   Draw the belly line underneath.

   The belly is a separate decision from the masses: it hangs below the line joining them, sagging most midway, and how much it sags is part of the animal - taut on a deer, generous on a cow. Draw it as one curve, not two arcs meeting.

   Tarira A straight line between the ovals, which reads as a table.

   Check The belly should dip below both mass bottoms at its middle.

8. Step 8

   Draw the chest front down, and the rump around.

   Two curves seal the body into one shape: down the front of the chest into the belly, and from the top of the hips around the rump to meet it. Without them the animal has no front or back and the legs float - this is the step that turns parts into a body.

   Tarira Leaving the ends open because the ovals suggest them.

   Check You should be able to trace the whole body without lifting your pen.

9. Step 9

   Run the front legs down from the chest mass.

   Legs are chains of segments with a joint at each bend, and every leg bends somewhere. Draw joint to joint in straight strokes first; curves come later if at all.

   Tarira Straight tube legs with no joints, which read as furniture.

   Check Each front leg should bend at least once.

10. Step 10

    Add the rear legs, checking their length against the front.

    The hind legs fold the opposite way to the front pair - the hock points backwards. Compare their length against the front legs rather than judging them alone.

    Tarira Back legs bending the same way as the front ones.

    Check Front and back feet should reach the same ground line.

11. Step 11

    Place the ears, and get their shape right.

    Ears attach further back on the skull than feels natural, and their shape is one of the strongest species signals you have. Draw the second by comparing it to the first.

    Tarira Planting the ears on top of the head like handles.

    Check Both ears should attach behind the midpoint of the skull.

12. Step 12

    Draw the front of the head - muzzle, nose, eye.

    The muzzle projects forward from the lower half of the head mass. Its length relative to the skull is the proportion to measure - it is the one that changes species when you get it wrong.

    Tarira A muzzle pointing down instead of forward.

    Check The eye should sit in the top half of the head mass.

13. Step 13

    Draw the tail and any remaining features.

    Detail is suggested, never itemised. Put the marks where they identify the animal and stop early - texture spread evenly everywhere flattens the drawing back out.

    Tarira Covering the body evenly in fur marks.

    Check Step back: the big shapes should still read first.

14. Step 14

    Draw the eye properly - iris, dark pupil, a dot of light.

    An eye is built in layers - iris, pupil inside it, one small highlight, and the brow line above that gives it a direction to look. The highlight and pupil must not touch, and the brow is what turns a circle into a gaze. This one feature carries more life than the rest of the head together.

    Tarira A single black dot, which reads as a bead.

    Check The highlight should sit at the pupil's edge, not inside it.

15. Step 15

    Draw all four feet: base, then the toe line.

    A leg without a foot is a pole. One short base line at the bottom of each leg, angled with the ground, plus a single toe split, and all four legs suddenly bear weight. Feet are also where the ground line will attach, so place all four bases at nearly the same height.

    Tarira Legs ending in points, or feet at four different heights.

    Check All four feet should sit within one pencil-width of the same line.

16. Step 16

    Anchor it: ground line, then the shadow under the pig.

    The ground is one line through the feet, and the cast shadow is one flattened arc beneath the body, darkest between the legs. Together they anchor the animal - without them even a perfect construction floats in white space. Keep the shadow tight under the body; a wide puddle reads as water.

    Tarira Skipping it, leaving the animal hovering.

    Check The shadow should touch at least two of the feet.

17. Step 17

    Put fur on the pig: a few tufts at the soft edges.

    Fur is an edge event: a few tufts where the coat genuinely hangs - chest, belly, rump - and nowhere else. Each tuft leans the way the coat grows, back and down, and the outline should still read as one body between them. This is also where the sealed construction line stops looking mechanical.

    Tarira Scalloping the entire outline evenly, which turns any animal into a sheep.

    Check Most of the outline should still be smooth between the tufts.

18. Step 18

    Shade the pig - underside first, one direction.

    Two or three patches of parallel strokes - under the belly, behind the shoulder - all leaning the same way, and the drawing suddenly has light in it. Keep the patches small: shading in a sketch is a note about where the dark lives, not a rendering.

    Tarira Scrubbing tone everywhere, which flattens the sketch it took fifteen steps to build.

    Check All the hatch strokes should lean the same direction.

19. Step 19

    Go round the keepers heavily, then erase the guides.

    Press harder on the outline and the face, leave the small marks light, and erase the construction ovals. That weight difference is what makes the drawing look decided.

    Tarira Going over every line at the same weight.

    Check The outline should be clearly darker than the interior marks.