How to Draw a Mug

Қадами ба қадам

1. Қадам 1

   Ба риштаи мӯй мӯйчаи мӯйча

   Everything about the ellipses follows from this. If the mug is below your eye level you will see into it; if it is level you will not. Make the decision consciously now rather than letting it drift halfway through the drawing.

   Диққат Not deciding, then drawing a rim that contradicts the base.

   & Озмоиш You should be able to say whether you are looking down into this mug or across at it.

2. Қадам 2

   Кашидани ришта ҳамчун як эллипси, дар як ҳаракати тез.

   Go round three or four times without stopping and keep the best pass. Speed is what makes an ellipse smooth - drawn slowly it comes out lumpy on one side every single time, because your hand cannot hold a curve at low speed.

   Диққат Building it out of short careful arcs.

   & Озмоиш It should be symmetrical about its own long axis.

3. Қадам 3

   Дар ду тарафи тахтачаи тахтасанг ду риштаи ғафс гузошта мешавад.

   Start exactly at the ends of the ellipse's long axis. A slight taper inward looks more natural than perfectly parallel sides, and it is what most real mugs do.

   Диққат Starting the sides inside or outside the rim, which leaves a visible step.

   & Озмоиш Each side should begin exactly at the widest point of the rim.

4. Қадам 4

   Пӯшидани поён бо эллипс каме калонтар аз боло.

   The base is further from your eye level than the rim, so it is rounder. Same width, more curve. Getting this relationship right is the difference between a mug that sits on the table and one that appears to be sliding off it.

   Диққат Drawing the base flatter than the rim, or as a straight line.

   & Озмоиш Rounder than the rim, and exactly the same width.

5. Қадам 5

   Афзудани хати каҷи конусшакл

   This thin band is the thickness of the ceramic, and it is what makes the top read as an opening rather than a painted disc. One stroke, following the rim's curve.

   Диққат Drawing it parallel all the way round instead of following the ellipse.

   & Озмоиш There should be a visible band between the two curves at the front.

6. Қадам 6

   Кашидани хати каҷ

   Start just below the rim and end about two-thirds of the way down the side. Both ends must touch the mug - a handle that floats beside the body is the most common error here and it is instantly visible.

   Диққат Leaving a gap where the handle meets the mug.

   & Озмоиш Both ends of the curve should touch the side of the mug.

7. Қадам 7

   Даровардани ғафсии гардонанда бо дуюми хати каҷи дар дохили.

   A handle is a strap, not a wire. The inner curve runs parallel to the outer one and meets the mug slightly closer in at both ends. This is a small change that makes a large difference to how solid the mug looks.

   Диққат Drawing the handle as a single line.

   & Озмоиш There should be a visible gap between the two handle curves.

8. Қадам 8

   Ба ҷое, ки нур меояд, ишора кунед.

   Pick a side and commit. A cylinder shades differently from a sphere - the darkest band sits just inside the edge on the shadow side, not at the very edge, because light bounces back up off the table onto the rim.

   Диққат Shading the very edge darkest, which makes the mug look flat.

   & Озмоиш You should be able to say which side is lit.

9. Қадам 9

   Дар ин ҷо барои дарёфти нури офтоб аз нури офтоб истифода мебаранд.

   Work in one direction rather than scrubbing back and forth. Scrubbing gives an even grey, which is exactly the thing that makes a drawing look flat, so lay the strokes the same way and build the darkness in passes.

   Диққат Being too timid. Beginners routinely stop two or three steps short of dark enough.

   & Озмоиш The dark side should be clearly darker than the mid tone, not slightly.

10. Қадам 10

    Add a lighter strip right at the shadow-side edge.

    Light bouncing off the table catches the very edge of a cylinder, so the darkest band sits slightly INSIDE the outline. Leaving that thin lighter strip is what makes the mug read as round rather than as a shaded rectangle.

    Диққат Running the shading right up to the outline.

    & Озмоиш There should be a thin lighter line between your shading and the edge.

11. Қадам 11

    Сояро ба сатҳи поён илова кунед.

    The cast shadow is darkest where it touches the mug and softens as it moves away. It also anchors the object to a surface - without it the mug floats, however well you have shaded it.

    Диққат Drawing it as an even grey blob detached from the object.

    & Озмоиш It should touch the object and be darkest at that contact point.

12. Қадам 12

    Дар болои хатҳое, ки мехоҳед нигоҳ доред, гузаред ва роҳнамоҳоро гум кунед.

    This is the step that turns a construction drawing into a finished one, and it is the one most people skip. Press harder on the outline and the features; leave the small stuff light. That difference in weight is what makes a drawing look deliberate rather than traced, and it costs thirty seconds.

    Диққат Going over everything at the same weight, which flattens the drawing back out.

    & Озмоиш The outline should be clearly darker than the smallest details.