How to Draw a Candle
1 / 12
Draw the eye-level guide.
You should be able to say if you are above or level with the rim.
Drawing on paper instead?
We straighten and clean up the photo for you. Paper counts exactly the same.
About this drawing
A candle is a cylinder with a soul: the wax column is the jar lesson again, but the flame is a new problem - a teardrop that must read as light, which means it is the one thing on the page you barely touch. The flame stays paper-white; everything NEAR it darkens instead, and the melted rim drips break the top ellipse.
Underneath, this is the same two-ellipse build as every cup and bottle here; the object lives in the profile between them.
Step by step
-
Step 1
Draw the eye-level guide.
Everything about the ellipses follows from where your eye is. Decide now, consciously, and mark it - letting it drift mid-drawing is how the rim and base end up disagreeing.
Watch out Not deciding, then drawing contradictory ellipses.
Check You should be able to say if you are above or level with the rim.
-
Step 2
Draw the opening as one ellipse.
Round three or four times in one fast continuous motion and keep the best pass. Speed is what makes an ellipse smooth - drawn slowly it lumps on one side every time.
Watch out Building the ellipse from four careful arcs.
Check The rim should be symmetrical about its long axis.
-
Step 3
Draw the walls down to the base.
Start each side exactly at the widest point of the rim ellipse. A step where side meets rim is instantly visible and almost impossible to hide later.
Watch out Sides starting inside or outside the rim's ends.
Check Each side should leave the rim at its widest point.
-
Step 4
Close the bottom with a rounder curve.
The base is further from your eye than the rim, so it is ROUNDER - same width, more curve. Getting this backwards is what makes vessels look like they are sliding off the table.
Watch out A base flatter than the rim, or a straight line.
Check The base curve should be rounder than the rim.
-
Step 5
Put a second curve just inside the top.
One curve just inside the rim gives the material its thickness and turns the top from a painted disc into an opening. It follows the rim's curve, not parallel all the way round.
Watch out Skipping it, leaving a flat disc on top.
Check A visible band should separate the two curves at the front.
-
Step 6
Add the neck of the candle.
Where the profile changes is where the form lives. Draw the change on both sides at the same height - a shoulder at two heights makes the whole vessel lean.
Watch out The profile changing at different heights left and right.
Check Both sides should change shape at the same height.
-
Step 7
Add the handle - a strap, not a wire.
Both ends must touch the body - a floating handle is the most common error on any vessel. And it is a strap with thickness, never a single line.
Watch out A handle drawn as one wire line, or floating.
Check Both handle ends should touch the vessel's side.
-
Step 8
Add what makes it a candle.
The identifying details go on last and they follow the form - a label, a pattern or a spout curves with the surface it sits on.
Watch out Flat detail pasted over a round form.
Check Any pattern should bend with the body.
-
Step 9
Shade the shadow side.
A cylinder's darkest band sits just INSIDE the shadow edge, not at it. Lay the strokes vertically, following the form, and build up in passes.
Watch out Scrubbing horizontal tone across a vertical form.
Check The darkest band should sit inside the outline.
-
Step 10
Keep a light line right at the dark edge.
Light bounces off the table back onto the very edge, so leave a thin lighter strip at the outline. That strip is what makes the form read as round rather than flat-shaded.
Watch out Shading right up to the edge.
Check A light strip should separate shading from outline.
-
Step 11
Add the shadow on the table.
Darkest where it touches the base, softening as it spreads. The cast shadow is what anchors the vessel - without it the thing floats no matter how well you shaded it.
Watch out A detached grey blob nearby.
Check The shadow should touch the base.
-
Step 12
Weight the outline, lose the construction.
Weight the rim and the silhouette, erase the eye-level guide, and check the two ellipses one last time - they are what the whole drawing stands on.
Watch out Leaving the eye-level line in.
Check Rim and silhouette should be the darkest lines.
What it looks like finished
The same drawing with every guide erased and only the lines you meant to keep, at the weight you meant them to be. If yours still has centre lines and blocking-in shapes in it, this is the step you have not done yet - and it takes about thirty seconds.
Yours will not look like this, and it is not supposed to. This is the construction with the scaffolding taken away, not a drawing somebody made to be admired - the point is to show you which of your lines were guides.
What this one actually teaches you
This is an ellipse lesson wearing a household object. The rim and base must agree about your eye level, and learning to make them agree fixes wheels, plates and hats at the same time.
The candle teaches drawing light by omission: the brightest thing on the page is the least worked, defined entirely by the tones around it. It is the highlight rule from the solid family, promoted from accent to subject.
Practise these: Line confidence Proportion Value range
What you need
A pencil and any paper, or a finger on the canvas above - nothing here needs special equipment. Keep the construction light if you are on paper, because the guides come off at the end.
If it's going wrong
If the flame looks solid, you shaded it: a flame is drawn by contrast - leave it white, darken around it, and give it one inner teardrop for the core.
If the top edge is too clean, melt it: one or two drips running from the rim, each a narrow U hanging over the edge, break the ellipse honestly.
If the wick is wrong, it is too long or too straight - a burnt wick is short and curls, one small dark hook between wax and flame.
Print the steps
Take it away from the screen. The step sheet prints on one page.
Questions people ask
- How do I draw a candle flame?
- By not drawing it: leave the teardrop white, add one inner teardrop for the core, and darken the area AROUND it. Light on paper is always the tone of its surroundings.
- How do I draw melted wax drips?
- One or two narrow U-shapes hanging over the rim, different lengths, breaking the top ellipse. More than three reads as a cave formation.
- How long should a candle's wick be?
- Short and curled - one small dark hook between wax and flame. A long straight wick reads as unlit even with a flame drawn on it.
- Can I draw a candle on paper instead of the canvas?
- Yes - print the step sheet and draw beside it. The ellipse practice actually benefits from paper, where your whole arm is free, and a photo of the page gets measured exactly like a canvas drawing.
- How do I draw the top of a candle?
- As one fast ellipse, going round several times and keeping the best pass. Its roundness depends on your eye level - decide that first.
- Why does my candle look like it is tipping over?
- The base ellipse disagrees with the rim. The base is always slightly ROUNDER than the rim, never flatter, and both must be the same width.
- Can a beginner draw a candle?
- Yes, and it is worth it - the ellipse practice transfers directly to wheels, plates, hats and eyes. There is a finish-early step partway through.
- How do I shade a candle?
- Vertically, following the form, darkest just inside the shadow edge with a thin light strip at the very edge - that strip is what makes it read as round.
- What is the hardest part of drawing a candle?
- The two ellipses agreeing with each other. Everything else is forgiving; the rim and base are what the eye checks first.